Brenda Lynn

This photo of Brenda Lynn Acevedo, found on the Bella Donna blog, caught my eye for a couple reasons. Firstly, having her arms (and, in my imagination her legs) held either flat or vertically makes them easy to print without support; and then of course there is the way that her breasts gently rest on the floor giving them a profile that reminds me of a Piet Hein superegg (go and look it up and you'll see what I mean).

The fluid nature of (natural) breast tissue means that it naturally reshapes itself in response to gravity. (Of course, the same is true of all fatty tissue, but the models in these photos don't usually have much surplus fat in other places, so this issue generally only affects the breasts.) Character modelling software allows you to position the limbs, trunk and head in anatomically plausible positions, but also allows you to change the shape, size and position of the breasts. One thing that it doesn't do very well though is to model the impact of gravity on mobile breast tissue; there are add-on pieces of morphing software that give an additional level of control, but nothing I have found yet that mimics the effect of gravity on natural breasts in a reclining position.

So, after exporting the best pose I could manage from the posing software, I started sculpting in Blender until the breasts had a shape I was happier with and which I was ready to try printing. 

Feeling lazy, I used the clock rewind trick to bring Project Miller back to life again and quickly generated a single watertight mesh from the multi-object base and then did one more smoothing iteration.
I used Simplify3D for the slicing and made sure there was plenty of support material around the right arm so that the small point of elbow contact with the bed wasn't put at risk of failure.
I decided to use a nice wood-coloured PLA from 3D Filaprint and after a long 16 hour print this is what the printer produced.

Opinion: I'm generally very pleased with this one. There are couple of areas that could be improved - some distortion around the heel, and rather too little support material in the small of the back and between the shoulder blades.

Postscript: I decided to adjust the layer positions and try a reprint. This one came out even better.

Yoga interrupted

My third and final sculpture this week is a mashup of two more photos I found on Belladonna's Tumblr blog. I wanted to use the top half of this photo ...

... and the bottom half of this painting by Giuseppe Gigli ...

... combined in a single pose.

Getting the feet into position was the most difficult part.

I am already a total convert to the idea of 'micro-layering - printing the external skin at 0.1 mm layer height but the support and infill at 0.3 mm layer height, so infill is only laid down every third layer. One of the new features I have been experimenting with is 'infill zoning'.

• Starting at the bottom, Zone 1 uses 25% infill.
• The top surfaces of the calves, thighs and feet are in Zone 2 and use 40% infill.
• The trunk, arms and head in Zone 3 revert to 25% infill.
• The top of the head uses 50% infill.

You can just about see the four zones in this reverse cross-section view (click to enlarge).

This uses less infill material where it is not needed, saving time and money, but increases the level of internal support where important top surfaces need to be laid down smoothly. 

The support material generated by Simplify3D worked reasonably well but left the undersides of the elbows and calves a little rougher than I would have liked.

Reflections

Here is the first of three new prints I have been working on recently.

'Reflections' came to my attention when Bruno Birkhofer posted a different picture on Google+ last week. All his pictures are beautiful but, once again, it was one of his black and white portraits that inspired me to try another sculpture.

Modelling the pose in my favourite character modelling program was fun, as usual, but it proved particularly tricky to place the hands in exactly the right position. Several of the joint movement ranges have to have their range limitations turned off just to get close. 

In a moment of over-zealous optimism I decided to replicate the model's facial expression and kept the eyes closed but the mouth open. This involved a significant amount of cleaning up in Blender for a detail that ultimately proved too small to show in the final print. 

Not to worry - one day I may be able to sell these models and perhaps I'll even be able to afford a nice high-resolution DLP printer like the Kudo3D and then they will look even better.

I'm now getting the hang of using Simplify3D to slice my models so that the support material is placed where it's needed. The only thing I got wrong this time was placing insufficient support underneath the ponytail. The tip broke free during printing but fortunately the print managed to correct itself leaving enough to look reasonably OK.

Here's a couple of photos of the final print using translucent coffee-coloured PLA from 3D Filaprint, at 0.1 mm layer resolution with support enabled.

Close-up reproducing the pose in Reflections

The full model, showing a nice reflection of its own

Kayleigh

One of the most beautiful poses I've seen recently on Pinterest was this one.

It had been repinned many times, so clearly other people agreed with me, but wasn't being properly credited. I used Google image search to track down the original version and discovered that the model is Kayleigh Lush.

I used my favourite character modelling software to emulate the pose (not exactly right, but good enough to capture the spirit of the picture, I hope) and then exported an OBJ file. I then used Blender to correct the orientation and scale and to flatten the base and remove the eyelashes, before exporting an STL file.

Here is the screen capture of the 3D model in Blender.

This time I used Project Miller again to select the external surfaces of the model, then used Kisslicer to generate the gcode file with full support turned on and printed in white PLA from Faberdashery at 0.15 mm resolution. 

Another pretty successful print, in my view.

With hindsight, it might have been better to have sliced with Cura and used the expert setting called 'Fix Horrible' - type B, which closes all internal holes and deals much more nicely with limb overlaps. Maybe next time.

Golden Sun

I had this idea that I wanted to try and print a version of Sun Worship using gold filament. I had read some good things about the gold PLA from Faberdashery so I decided to give it a try.

First though, I decided to spend some time rebuilding the pose from scratch. I've also been getting better at using the Sculpt tool in Blender and wanted to have another go at a better hairstyle. Here she is in Blender.

Getting the hands and feet to sit absolutely flat on the floor really helps to keep the print stable.
Good adhesion to the print bed is vital when printing tall sloping limbs without support. Here you can see the point just before the arm connects to the shoulder - perfectly level and no warping thanks to a cooling fan.

The final print came out even better than I had hoped for. My recent upgrades to the nozzle and belts seem to be giving me very nice smooth prints now. And of course, being PLA, acetone vapour baths are not an option - this glossy finish is straight off the printer.

Metamorphosis

This weekend I created a new sculpture based on the photo of Edward Watson performing in Kafka's The Metamorphosis. I tried to reproduce the pose as accurately as possible and was very pleased with the result.

 I had hoped to print the sculpture without turning on the automatic support feature in the slicing software, but as soon as I had finished posing the model it was clear that this would not be possible. As well as the shallow slopes on the thigh and arm, there were points, on the tip of the chin and the underside of the breasts, that had nothing beneath them. 

I used Kisslicer to turn the STL model into printer instructions and enabled medium support. This time I decided to try printing at 150 micron resolution to reduce the visibility of the layers. I also wanted to find out how well the support material could be removed from a PLA print so I used a translucent blue filament for the 12 hour print.

The support material was more difficult to remove from PLA than with the grey ABS, but after a bit of work it came away surprisingly cleanly.

Here is a quick video of the model on a turntable to show it from all angles.

http://youtu.be/MRIWulQLC5U

And here are a few photos.